Hall Technologies UHBX-WPC-P2 HDMI over UTP Extender with HDBaseT and PoH (Wall Plate Sender + Receiver)

UHBX-WPC-P2 is an extender kit ( combination of UHBX-SC-WP + UHBX-R-PSE ) from Hall Research that utilizes HDBaseT™ technology. It can send HDMI, IR, bi-directional RS-232, and PoH (Power-over-HDBaseT™) to 500 ft (150 m) on a single Cat6 cable. The extender uses only one +5v power supply, internally creates 48v PoH and complies with IEEE 802.3af handshake. The P2 extender’s receiver unit provides power to the sender. In standard mode the UHBX-WPC-P2 supports DVI and HDMI signals of virtually any resolution up to 4K x 2K to 330 ft (100m), and in Long Reach mode it supports resolutions to 1920×1080 to 500 ft (150 m). The devices are housed in compact and sturdy metal enclosures and have convenient mounting provisions. They are designed and manufactured in the USA.
The end identified as PSE (power sourcing equipment) injects power on to the Cat6 cable and the side identified as WP (Wall Plate) is powered through the Cat6 cable. The PSE side requires connection of an AC adapter that supplies 5v DC, while the WP side is simply powered through the RJ45 connector from the opposite side.

Full-duplex RS232 Serial Port extension is provided that can operate at any baud rate to 115,200 (independent of video activity). The extender can also extend IR from one end to the other. IR Detector and IR Emitter cables are sold separately. The IR extension preserves the modulation(carrier) frequency and provides compatibility to virtually any standard. It supports modulation range from 30 KHz to 60 KHz.

Two user selectable distance modes are available: Standard(default) and Long Reach. If the length of UTP cable is less than 100 meters (330 ft), then STD mode should be used. For the lengths above 330 ft Long Reach (L.R.) mode must be set. Long Reach setting can extend maximum of [email protected] Hz, 8-bit color (does not support deep-color or 4Kx2K) , RS232, IR and Power up to 500ft (150m)

Extends HDMI or DVI video to 500 ft on just one Cat6
Includes RS232 and IR extension in both directions
Supports virtually all HDMI and DVI resolutions including 4Kx2K
Only one end requires power, other side is powered via UTP
Power-over-HDBaseT™ meets IEEE 802.3af standard
Sturdy metal enclosures with mounting provisions
Complies fully with HDBaseT™ standard
Runs from just one +5vDC supply
RS232 Supports all baud rates regardless of presence of video
IR extension is carrier frequency agnostic and supports 30 KHz to 60 KHz modulation to provide compatibility across all IR standards
Fully isolates ground between TX and RX sides
Compact, Rugged, Reliable, and Economical
Made in USA

Max Distance Standard Mode (STD): 330 ft (100m)
Long Reach Mode (LR) : 500 ft (150m)
Video Standards DVI (single link) and HDMI (compliant with HDMI 1.4 video specifications including 12 bit color depth, 3D video and 4K support)
Signal Type TMDS
Connectors Locking HDMI
Video Resolutions DVI: VGA (640×480) to WUXGA (1920×1200)
HDTV: 480i to 1080p
Digital Cinema: 4K (4096×2160)
Supports [email protected] Hz (4:2:0 8 bit color) or [email protected] Hz (4:4:4 and 8 bit color)
Audio Formats All HDMI Embedded Audio including: LPCM 7.1CH, Dolby TrueHD and DTS-HD Master Audio (32-192kHz sample rate)
DDC Pass-Thru DDC for reading EDID directly from remotely connected LCD and HDCP handshake
CEC Pass-Thru DDC for Consumer Electronics Control compatible devices
RS232 Bi-directional (full-duplex) any baud rate upto 115,200
IR Extended in both directions. Carrier modulation range from 30 KHz to 60
KHz
PoH Power-over-HDBaseT™ meets IEEE 802.3af standard. PD side identifies as
Class 2 (3.84–6.49 watts). Actual power consumption of PD side is 5.5 watts
max
Power Supply 100 VAC to 240 VAC, 50-60 Hz, external; 5 VDC, 3.2 A, regulated
Actual DC current (powering both –PSE and –PD sides) 1.8A max
Power Sender: 3.5 watts (12 BTU) maximum
Receiver: 5.5 watts (19 BTU) maximum
Temp/humidity Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, non-condensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, non-condensing
Cooling Convection
Mounting End plates have L bracket with hole for surface mounting
Enclosure Metal (Steel ends and Aluminum extrusion)
Dimensions 1.18″ H x 4.13″ W x 4.57″ D (30mm H x 105mm W x 116mm D) Depth excludes connectors
Product weight Sender: 9.3 oz (0.58 lb or 264 g)
Receiver: 10 oz (0.63 lb or 284 g)
Kit (shipping) 37 oz (2.3 lb or 1050 g) includes: sender, receiver, power supply, power cord, HDMI cable, manual, and packaging
Vibration ISTA 1A in carton (International Safe Transit Association)
Safety CE
EMI/EMC CE, FCC Class A
MTBF 90,000 hours (Calculated Estimate)
Warranty 2 years parts and labor