Description
The nX Series NX8002 2-Channel 800W Power Amplifier with Programmable Outputs from Ashly is a Class-D switching amplifier combined with a switch mode power supply. This amplifier meets the requirements of demanding live sound and fixed installation sound systems in stadiums, arenas, performance venues, worship spaces, and convention centers. The rear panel has DIP switches for programming each channel output for either High-Z or Low-Z operation.
Ashly NX8002 Specs
General
Voltage Gain Selectable at 26, 32, or 38 dB, and 1.4 V
Damping Factor >250 (8 Ω load <1 kHz)
Filter Input High Pass Filter: 80 Hz 2nd order
Distortion <0.5% SMPTE, typical
<0.5% THD-N, typical (8 Ω, 10 dB below rated power, 20 Hz to 20 kHz)
Channel Separation -75 dB (dB from full output, 1 kHz)
Signal / Noise 20 Hz to 20 kHz, un-weighted
>108 dB
Frequency Response 20 Hz to 20 kHz, ±0.05 dB
Connector Balanced Input Connector: Euroblock 3.5 mm, 1/4″ TRS and XLR combo jack
Input Impedance 10 kΩ
Maximum Input Level 21 dBu
Speaker Output Connector: Neutrik speakON
Level Control Remote DC: 4 x 3.5 mm Euroblock – Gnd, CV, V+ per input
Attenuation Front panel, software, offset link group, and remote per channel
Fully off = mute
Protection Circuits Inrush current limitation, temperature monitoring, output over-power protection, and mains fuses
Cooling Continuously variable temperature controlled axial fans
Environmental Non-condensing 32 to 113°F (0 to 45°C)
Power Requirements
Power At 50 Hz
Nominal (Automatic Sensing SMPS): 120 VAC
Operating Range: 70 to 135 VAC
Minimum Power-Up: 85 VAC
At 60 Hz
Nominal (Automatic Sensing SMPS): 240 VAC
Operating Range: 140 to 270 VAC
Minimum Power-Up: 170 VAC
Connector Power Cable Connector: 20 A powerCON
Maximum Output Power Per Channel, Low-Z Output, All Channels Driven
2/4/8 Ω: 800 W
Output Low Z Output, Bridge Mode, All Channels Driven: 1600 W (4/8 Ω)
70V, 100V Output, All Channels Driven: 800 W (70/100 V (per channel)
Power Draw Sleep Mode: < 1 W
Standby Mode: 25 W
Idle (No Signal): 40 W
Current Draw For 120 VAC
Sleep Mode: 0.1 A
Standby Mode: 0.38 A
Idle (No Signal): 0.70 AFor 240 VAC
Sleep Mode: 0.05 A
Standby Mode: 0.19 A
Idle (No Signal): 0.35 A
Maximum, All Channels Driven, Typical Input
1/8 Max Power @ 2 Ω): 4.6 A for 120 VAC, 2.3 A for 240 VACDissipation Thermal Dissipation: Sleep Mode: <3.4 BTU/hr
Standby Mode: 85 BTU/hr
Idle (no signal): 136 BTU/hr
Typical (1 / 8 Max Power @ 2 Ω): 495 BTU/hr
LED Indicators Front Panel LED Indicators
White: Power Switch: On, off, standby (flashing)Red LED:
Clip / Mute Per Channel: Clip @ 1 dB below full output / mute
Protect: On (fault condition or shut down), OffGreen LED:
Signal Per Channel: -18 dBu, below rated output
Bridge Per Channel Pair: On, off
Com: On, for Ethernet data or device ID
Current Per Channel: Proportional to outputYellow LED:
Temperature Per Channel: On dim at 90% maximum operating temperature, full bright + protect at 100%
Sleep: On, amplifier is asleep from audio inactivity
Disable: On, power switch & front panel attenuators are disabledDimensions 19.0 x 3.5 x 16.8" (48.3 x 8.9 x 42.8 cm)
Weight 27.6 lb (12.5 kg)
Packaging Info
Package Weight 29 lb