Ashly nXe Series NXE8002 2-Channel 800W Power Amplifier with Programmable Outputs & Ethernet Control

Network Multi-Mode Power Amplifier 2 x 800 Watts @ 2/4/8 Ohms or 25V/70V


Ashly nXe Series NXE8002 2-Channel 800W Power Amplifier with Programmable Outputs & Ethernet Control

Weight 29 lbs
Dimensions 19 × 3.5 × 16.8 in
Part No

SKU nXe8002 Categories ,

Product Description

The nXe Series NXE8002 2-Channel 800W Power Amplifier with Programmable Outputs & Ethernet Control from Ashly is a Class-D switching amplifier combined with a switch mode power supply. This amplifier meets the requirements of demanding live sound and fixed installation sound systems in stadiums, arenas, performance venues, worship spaces, and convention centers.

The rear panel has DIP switches for programming each channel output for either High-Z or Low-Z operation. This amplifier can be connected to a network with Ethernet control and features serial data control, aux preamp outputs, instant standby mode, preset recall, fault condition logic outputs, and optional network audio and digital audio capability, all controlled using the Protea Software Suite (not included).

2-Channel high-output amplifier with programmable output on each channel (High-Z or Low-Z, selected via rear panel DIP switches)
Power-saving, Energy Management System with automatic <1W sleep-mode (defeatable)
Front panel power switch and level controls (can be disabled for security)
Rear panel DIP switches per channel for selection of high pass filter, limiter, input gain, and High-Z or Low-Z speaker output configuration
Remote DC level control on each input channel
Switch mode power supply automatically detects 120 or 240VAC operation
Extensive protection circuitry and continuously variable cooling fans
Multiple independent internal power supplies provide increased channel separation and reliability
Ethernet port for control and monitoring of amplifier functions, with front panel COM activity LED
Serial data port for use with Ashly remote control devices, or optional RS-232 converter for third party controllers (not included)
Protea software allows to remotely disable all front panel controls, including the on/ off switch, for a tamper-proof installation
Real-time clock with event scheduler
Instant standby mode that can be triggered by contact closure, software control, or event scheduler for reduced power consumption
Programmable power-on delay
Preset recall via contact closure, software control, remote control, or event scheduler
Aux preamp outputs, and fault condition logic outputs
Optional Cobranet or Dante network audio and AES3 digital audio input with pass-through
Neutrik Combo XLR – 1/4″ TRS jack plus Euroblock input connectors
Neutrik speakON twist locking loudspeaker connectors for security, safety, and reliability
Neutrik powerCON detachable AC mains connector
Made in USA

Ashly NXE8002 Specs
Voltage Gain Selectable at 26, 32, or 38 dB, and 1.4 V
Damping Factor >250 (8 Ω load <1 kHz) Filter Input High Pass Filter: 80 Hz 2nd order Distortion <0.5% SMPTE, typical <0.5% THD-N, typical (8 Ω, 10 dB below rated power, 20 Hz to 20 kHz) Channel Separation -75 dB (dB from full output, 1 kHz) Signal / Noise 20 Hz to 20 kHz, un-weighted >108 dB
Frequency Response 20 Hz to 20 kHz, ±0.05 dB
Connector Balanced Input Connector: Euroblock 3.5 mm, 1/4″ TRS and XLR combo jack
Input Impedance 10 kΩ
Maximum Input Level 21 dBu
Speaker Output Connector: Neutrik speakON
Network Control Network: Compatible with standard 100 MB Ethernet
AUX Outputs Connector: Balanced Euroblock 3.5 mm
Maximum Output Level: 21 dBu
Contact Closure Remote Standby: Euroblock 3.5 mm, close contact to GND for standby mode
Preset Recall: Euroblock 3.5 mm, close contact to GND for preset 1-4 recall
Data Data Connection: Euroblock 3.5 mm – Gnd, 18 V, in, out
Outputs Fault Condition Logic Outputs: 4 x 3.5 mm Euroblock
Level Control Remote DC: 4 x 3.5 mm Euroblock – Gnd, CV, V+ per input
Attenuation Front panel, software, offset link group, and remote per channel
Fully off = mute
Protection Circuits Inrush current limitation, temperature monitoring, output over-power protection, and mains fuses
Cooling Continuously variable temperature controlled axial fans
Environmental Non-condensing 32 to 113°F (0 to 45°C)
Power Requirements
Power At 50 Hz
Nominal (Automatic Sensing SMPS): 120 VAC
Operating Range: 70 to 135 VAC
Minimum Power-Up: 85 VAC

At 60 Hz
Nominal (Automatic Sensing SMPS): 240 VAC
Operating Range: 140 to 270 VAC
Minimum Power-Up: 170 VAC
Connector Power Cable Connector: 20 A powerCON
Maximum Output Power Per Channel, Low-Z Output, All Channels Driven
2/4/8 Ω: 800 W
Output Low Z Output, Bridge Mode, All Channels Driven: 1600 W (4/8 Ω)
70V, 100V Output, All Channels Driven: 800 W (70/100 V (per channel)
Power Draw Sleep Mode: < 1 W Standby Mode: 25 W Idle (No Signal): 40 W Current Draw For 120 VAC Sleep Mode: 0.1 A Standby Mode: 0.38 A Idle (No Signal): 0.70 A For 240 VAC Sleep Mode: 0.05 A Standby Mode: 0.19 A Idle (No Signal): 0.35 A Maximum, All Channels Driven, Typical Input 1/8 Max Power @ 2 Ω): 4.6 A for 120 VAC, 2.3 A for 240 VAC Dissipation Thermal Dissipation: Sleep Mode: <3.4 BTU/hr Standby Mode: 85 BTU/hr Idle (no signal): 136 BTU/hr Typical (1 / 8 Max Power @ 2 Ω): 495 BTU/hr LED Indicators Front Panel LED Indicators White: Power Switch: On, off, standby (flashing) Red LED: Clip / Mute Per Channel: Clip @ 1 dB below full output / mute Protect: On (fault condition or shut down), Off Green LED: Signal Per Channel: -18 dBu, below rated output Bridge Per Channel Pair: On, off Com: On, for Ethernet data or device ID Current Per Channel: Proportional to output Yellow LED: Temperature Per Channel: On dim at 90% maximum operating temperature, full bright + protect at 100% Sleep: On, amplifier is asleep from audio inactivity Disable: On, power switch & front panel attenuators are disabled Dimensions 19.0 x 3.5 x 16.8" (48.3 x 8.9 x 42.8 cm) Weight 28.7 lb (13.1 kg) Packaging Info Package Weight 29 lb