Ashly NXE3.02 Specs
General
Voltage Gain Selectable at 26 dB, 32 dB, 38 dB, or 1.4 V
Damping Factor >250 (8 Ω load <1 kHz) Filter Input High Pass Filter: 80 Hz 2nd order Distortion <0.5% SMPTE, typical <0.5% THD-N, typical (8 Ω, 10 dB below rated power, 20 Hz to 20 kHz) Channel Separation -75 dB (dB from full output, 1 kHz) Signal / Noise 20 Hz to 20 kHz, un-weighted >114 dB (all 3.0x models)
Frequency Response 20 Hz to 20 kHz, ±0.05 dB
Connector Balanced Input Connector: Euroblock 3.5 mm, 1/4″ TRS and XLR combo jack
Input Impedance 10 kΩ
Maximum Input Level +21 dBu
Speaker Output Connector: Neutrik & speakON
Network Control Network: Compatible with standard 100 MB Ethernet
AUX Outputs Connector: Balanced Euroblock 3.5 mm
Maximum Output: 21 dBu
Contact Closure Remote Standby: Euroblock 3.5 mm, close contact to GND for standby mode
Preset Recall: Euroblock 3.5 mm, close contact to GND for preset 1-4 recall
Data Data Connection: Euroblock 3.5 mm – Gnd, +18 V, In, Out
Level Control Remote DC: Euroblock 3.5 mm – Gnd, CV, V+ per input
Attenuation Front panel, software, offset link group, and remote per channel
fully off = mute
Amplifier Amplifier Protection: Inrush current limitation, temperature monitoring, output over-power protection, mains fuses
Cooling Continuously variable temperature controlled axial fan(s)
Environmental Non-condensing 32 to 113ºF (0 to 45ºC)
Power Requirements
Power At 50 Hz
Nominal (Automatic Sensing SMPS): 120 VAC
Operating Range: 70 to 135 VAC
Minimum Power-Up: 85 VAC

At 60 Hz
Nominal (Automatic Sensing SMPS): 240 VAC
Operating Range: 140 to 270 VAC
Minimum Power-Up: 170 VAC
Connector Power Cable Connector: 20 A powerCON
Output For Max Output Power Per Channel, EIAJ Test Standard, 1 kHz, 20 Hz to 20 kHz, 1% THD & Low Z Output: 2 Ω: 3,000 W
4 Ω: 2,000 W
8 Ω: 1,250 W

For Low Z output, Bridge Mode, 20 Hz to 20 kHz & 1% THD:
4 Ω: 6,000 W

For Output Per Channel:
70 V: 2,450 W
100 V: 1,250 W
Note: All Channels Driven
Power Draw Sleep Mode: < 1 W Standby Mode: 40 W Idle (No Signal): 55 W Note: All Channels Driven Current Draw For 120 VAC Sleep Mode: 0.1 A Standby Mode: 0.70 A Idle (No Signal): 1.00 A For 240 VAC Sleep Mode: 0.2 A Standby Mode: 0.35 A Idle (No Signal): 0.5 A Maximum for all Channels Driven: For 120 VAC Typical: 14.7 A For 240 VAC Typical: 7.3 A Dissipation Thermal Dissipation: Sleep Mode: <3.4 BTU/hr Standby Mode: 136 BTU/hr Idle (no signal): 187 BTU/hr Typical (1 / 8 Max Power): 1,360 BTU/hr Note: All Channels Driven LED Indicators Front Panel LED Indicators: White LED: Power Switch: On, off, standby (flashing) Red LED: Clip / Mute Per Channel: Clip @ 1 dB below full output / mute Protect: On, Off Green LED: Signal Per Channel: -18 dBu Bridge Per Channel Pair: On, off Com: On, for Ethernet data or device ID Current Per Channel: Proportional to output Yellow LED: Temperature Per Channel: On dim at 90% max operating temperature, full bright + protect at 100% Sleep: On, amplifier is asleep from audio inactivity Disable: On, power switch & front panel attenuators are disabled Processor Input Source Protēa DSP Options: Analog, auto (net, AES3, analog) Note: All DSP functions can be linked to 1 of 16 link groups Limiter Brick Wall Limiter: Threshold: -20 to 20 dBu Ratio: Infinite Attack: 0.2 to 50 ms/dB Release: 5 to 1000 ms/dB Control Advanced Gate Controls: Key Engage Enable: Yes Key Frequency: 20 Hz to 20 kHz Key Bandwidth: 0.016 to 3.995 octave Gain Gain (with / without VCA): -50 to 12 dB, off, polarity invert Digital VCA Groups: 4 available Remote RD8C Gain: Enable per channel, 0 dB to -∞ WR-5 (neWR-5) Remote Gain: 0 to -50 dB, mute EQ Type For 31-Band Filter Type: Constant Q or proportional Bandwidth: 0.499 octave to 0.25 octave For Parametric 2,4,6, or 10 Band Frequency: 20 to 20 kHz Level: -30 to 15 dB Q Value: 0.016 to 3.995 octave For Hi / Low Shelf 6 / 12 dB/octave Frequency: 20 Hz to 20 kHz Level: -15 to 15 dB For All Pass Frequency: 20 Hz to 20 kHz For Variable Q HP / LP Frequency: 20 Hz to 20 kHz Q Value: 3.047 to 0.267 For Notch / Bandpass Frequency: 20 Hz to 20 kHz Q Value: 92.436 to 0.267 Crossover 2 Way, 3 Way, 4 Way Crossover & High Pass / Low Pass Filters Bessel & Butterworth Filters: 12 / 18 / 24 / 48 dB/octave Linkwitz-Riley Filter: 12 / 24 / 48 dB / octave Frequency: Off, 20 Hz to 20 kHz Delay Sampling Rate: At 48kHz (Input Time, Distance & Temperature) Speaker Delay: 0 to 21 ms Delay: 0 to 682 ms At 96 kHz (Input Time, Distance & Temperature) Speaker Delay: 0 to 10.6 ms Delay: 0 to 341 ms Audio Metering Range: -60 to 20 dBu Increments: 1 dB Peak Hold Indicator: Yes Signal Generator Pink Noise, White Noise, Sine Wave Signal Level: Off, -50 to 20 dBu Sine Wave Frequency: 20 Hz to12 kHz Processor Input A/D, Output D/A: 24 bit DSP Processors: 32-bit floating point Sample Rates: 48 kHz, 96 kHz Propagation Delay @ 48 kHz: 1.42 ms Propagation Delay @ 96 kHz: 0.71 ms Mixer Gain (0.5 dB Increments): Off, -50 to 12dB Mute: Per channel Auto-mixer Enabled: Per channel Global Auto-mixer Response: 0.01 to 2 sec Enable Ducking at Mixer: Yes Ducking LED: Per channel if enabled Metering: Level, auto-mixer level Filters Number: 12 In/Out per filter: Yes Lock per filter and global lock: Yes Filter Modes: Float, Restricted, Manual Filter Type: Notch, Parametric Filter Frequency Range: 20 Hz to 20 kHz Notch Filter: -∞ Parametric Filter: 15 dB to -30 dB Filter Bandwidth: 0.016 to 3.995 octave Detector Sensitivity: 5 levels Float Time: 5 minutes to 24 hours Compressor Threshold -20 to 20 dBu Ratio 1.2:1 to infinite Attack 0.2 to 50 ms Release 5 to 1000 ms/dB Detectors Peak / average Attenuation 2 available Metering In, out, attenuation, graphical Controls Level Target Level: -40 to 20 dBu Action Type Gentle, normal, aggressive, user defined Maximum Gain 0 to 22 dB Metering Input, gain, attenuation Ratio 1.2:1 to 10:1 Threshold -30 to 0 dB Gain 5 to 1000 ms/dB Hold 0 to 6 seconds Noise Characteristics Gain Maximum: -20 to 20 dB Minimum Base: -40 to 20 dB Gain Adjustment Range 0.2 to 20 s/dB Groups Link Groups: 16 available Input Channels ANC: 1 to 2 or 1 to 4 Threshold Range Noise: -40 to 20 dBu Ratio Program/Ambient Gain: 0.3:1 to 3:1 Metering Input level, attenuation, average noise Ducking Trigger Threshold: -80 to 20 dBu Ducking Release: 5 to 1000 ms/dB Ducking Depth: 0 to -30 dB, -∞ Enable Ducking at Matrix Mixer: Yes Metering: Input Gate Threshold -80 to 20 dBu Range Off, 100 to 0 dB Attack 0.2 to 50 ms/dB Release 5 to 1000 ms/dB Metering Key signal, gate LED, graphical Dimensions 19.0 x 3.5 x 16.8" (482.6 x 89.0 x 426.7 mm) Weight < 28.0 lb (12.7 kg) Packaging Info Package Weight 31 lb Box Dimensions (LxWxH) 19 x 16 x 4"