Ashly NXP3.04 Specs
General
Voltage GainSelectable at 26 dB, 32 dB, 38 dB, or 1.4 V
Damping Factor>250 (8 Ω load <1 kHz) FilterInput High Pass Filter: 80 Hz 2nd order Distortion<0.5% SMPTE, typical <0.5% THD-N, typical (8 Ω, 10 dB below rated power, 20 Hz to 20 kHz) Channel Separation-75 dB (dB from full output, 1 kHz) Signal / Noise20 Hz to 20 kHz, un-weighted >114 dB (all 3.0x models)
Frequency Response20 Hz to 20 kHz, ±0.05 dB
ConnectorBalanced Input Connector: Euroblock 3.5 mm, 1/4″ TRS, and XLR combo jack
Input Impedance10 kOhms
Maximum Input Level+21 dBu
Speaker OutputConnector: Neutrik & speakON
NetworkControl Network: Compatible with standard 100 MB Ethernet
AUX OutputsConnector: Balanced Euroblock 3.5 mm
Maximum Output: 21 dBu
Contact ClosureRemote Standby: Euroblock 3.5 mm, close contact to GND for standby mode
Preset Recall: Euroblock 3.5 mm, close contact to GND for preset 1-4 recall
DataData Connection: Euroblock 3.5 mm – Gnd, +18 V, In, Out
Level ControlRemote DC: Euroblock 3.5 mm – Gnd, CV, V+ per input
AttenuationFront panel, software, offset link group, and remote per channel
fully off = mute
AmplifierAmplifier Protection: Inrush current limitation, temperature monitoring, output over-power protection, mains fuses
CoolingContinuously variable temperature controlled axial fan(s)
EnvironmentalNon-condensing 32 to 113ºF (0 to 45ºC)
Power Requirements
PowerAt 50 Hz
Nominal (Automatic Sensing SMPS): 120 VAC
Operating Range: 70 to 135 VAC
Minimum Power-Up: 85 VAC

At 60 Hz
Nominal (Automatic Sensing SMPS): 240 VAC
Operating Range: 140 to 270 VAC
Minimum Power-Up: 170 VAC
ConnectorPower Cable Connector: 32 A powerCON
OutputFor Max Output Power Per Channel, EIAJ Test Standard, 1 kHz, 20 Hz to 20 kHz, 1% THD & Low Z Output: 2 Ω: 3000 W
4 Ω: 2000 W
8 Ω: 1250 W

For Low Z output, Bridge Mode, 20 Hz to 20 kHz & 1% THD:
4 Ω: 6000 W

For Output Per Channel:
70 V: 2450 W
100 V: 1250 W
Note: All Channels Driven
Power DrawSleep Mode: < 1 W Standby Mode: 70 W Idle (No Signal): 100 W Note: All Channels Driven Current DrawFor 120 VAC Sleep Mode: 0.1 A Standby Mode: 1.30 A Idle (No Signal): 1.85 A For 240 VAC Sleep Mode: 0.05 A Standby Mode: 0.65 A Idle (No Signal): 0.92 A Maximum for all Channels Driven: For 120 VAC Typical: 29.5 A For 240 VAC Typical: 14.7 A DissipationThermal Dissipation: Sleep Mode: <3.4 BTU/hr Standby Mode: 238 BTU/hr Idle (no signal): 340 BTU/hr Typical (1 / 8 Max Power): 2,720 BTU/hr Note: All Channels Driven LED IndicatorsFront Panel LED Indicators: White LED: Power Switch: On, off, standby (flashing) Red LED: Clip / Mute Per Channel: Clip @ 1 dB below full output / mute Protect: On, Off Green LED: Signal Per Channel: -18 dBu Bridge Per Channel Pair: On, off Com: On, for Ethernet data or device ID Current Per Channel: Proportional to output Yellow LED: Temperature Per Channel: On dim at 90% max operating temperature, full bright + protect at 100% Sleep: On, amplifier is asleep from audio inactivity Disable: On, power switch & front panel attenuators are disabled Processor Input SourceProtēa DSP Options: Analog, auto (net, AES3, analog) Note: All DSP functions can be linked to 1 of 16 link groups LimiterBrick Wall Limiter: Threshold: -20 to 20 dBu Ratio: Infinite Attack: 0.2 to 50 ms/dB Release: 5 to 1000 ms/dB ControlAdvanced Gate Controls: Key Engage Enable: Yes Key Frequency: 20 Hz to 20 kHz Key Bandwidth: 0.016 to 3.995 octave GainGain (with / without VCA): -50 to 12 dB, off, polarity invert Digital VCA Groups: 4 available Remote RD8C Gain: Enable per channel, 0 dB to -∞ WR-5 (neWR-5) Remote Gain: 0 to -50 dB, mute EQ TypeFor 31-Band Filter Type: Constant Q or proportional Bandwidth: 0.499 octave to 0.25 octave For Parametric 2,4,6, or 10 Band Frequency: 20 to 20 kHz Level: -30 to 15 dB Q Value: 0.016 to 3.995 octave For Hi / Low Shelf 6 / 12 dB/octave Frequency: 20 Hz to 20 kHz Level: -15 to 15 dB For All Pass Frequency: 20 Hz to 20 kHz For Variable Q HP / LP Frequency: 20 Hz to 20 kHz Q Value: 3.047 to 0.267 For Notch / Bandpass Frequency: 20 Hz to 20 kHz Q Value: 92.436 to 0.267 Crossover2 Way, 3 Way, 4 Way Crossover & High Pass / Low Pass Filters Bessel & Butterworth Filters: 12 / 18 / 24 / 48 dB/octave Linkwitz-Riley Filter: 12 / 24 / 48 dB / octave Frequency: Off, 20 Hz to 20 kHz DelaySampling Rate: At 48kHz (Input Time, Distance & Temperature) Speaker Delay: 0 to 21 ms Delay: 0 to 682 ms At 96 kHz (Input Time, Distance & Temperature) Speaker Delay: 0 to 10.6 ms Delay: 0 to 341 ms Audio MeteringRange: -60 to 20 dBu Increments: 1 dB Peak Hold Indicator: Yes Signal GeneratorPink Noise, White Noise, Sine Wave Signal Level: Off, -50 to 20 dBu Sine Wave Frequency: 20 Hz to12 kHz ProcessorInput A/D, Output D/A: 24 bit DSP Processors: 32-bit floating point Sample Rates: 48 kHz, 96 kHz Propagation Delay @ 48 kHz: 1.42 ms Propagation Delay @ 96 kHz: 0.71 ms MixerGain (0.5 dB Increments): Off, -50 to 12dB Mute: Per channel Auto-mixer Enabled: Per channel Global Auto-mixer Response: 0.01 to 2 sec Enable Ducking at Mixer: Yes Ducking LED: Per channel if enabled Metering: Level, auto-mixer level FiltersNumber: 12 In/Out per filter: Yes Lock per filter and global lock: Yes Filter Modes: Float, Restricted, Manual Filter Type: Notch, Parametric Filter Frequency Range: 20 Hz to 20 kHz Notch Filter: -∞ Parametric Filter: 15 dB to -30 dB Filter Bandwidth: 0.016 to 3.995 octave Detector Sensitivity: 5 levels Float Time: 5 minutes to 24 hours Compressor Threshold-20 to 20 dBu Ratio1.2:1 to infinite Attack0.2 to 50 ms Release5 to 1000 ms/dB DetectorsPeak / average Attenuation2 available MeteringIn, out, attenuation, graphical Controls LevelTarget Level: -40 to 20 dBu Action TypeGentle, normal, aggressive, user defined Maximum Gain0 to 22 dB MeteringInput, gain, attenuation Ratio1.2:1 to 10:1 Threshold-30 to 0 dB Gain5 to 1000 ms/dB Hold0 to 6 sec Noise Characteristics GainMaximum: -20 to 20 dB Minimum Base: -40 to 20 dB Gain Adjustment Range0.2 to 20 s/dB GroupsLink Groups: 16 available Input ChannelsANC: 1 to 2 or 1 to 4 Threshold RangeNoise: -40 to 20 dBu RatioProgram/Ambient Gain: 0.3:1 to 3:1 MeteringInput level, attenuation, average noise DuckingTrigger Threshold: -80 to 20 dBu Ducking Release: 5 to 1000 ms/dB Ducking Depth: 0 to -30 dB, -∞ Enable Ducking at Matrix Mixer: Yes Metering: Input Gate Threshold-80 to 20 dBu RangeOff, 100 to 0 dB Attack0.2 to 50 ms/dB Release5 to 1000 ms/dB MeteringKey signal, gate LED, graphical Dimensions19.0 x 3.5 x 16.8" (482.6 x 89.0 x 426.7 mm) Weight< 28.0 lb (12.7 kg) Packaging Info Package Weight32 lb Box Dimensions (LxWxH)19 x 16 x 4"