Description
The 1200W Crown Audio CDi 2|1200 2-Channel DriveCore Series Power Amplifier utilizes technology derived from the flagship Crown DriveCore Install series amplifiers, providing an impressive mix of high-performance, rich feature set, and competitive cost. The CDi DriveCore 2|1200 offers streamlined functionality for most large-sized installation such as cinema, houses of worship, hotels, cruise lines, and more.
The DriveCore integrated circuit eliminates hundreds of components within the amplifier, reducing the variability of component values and increasing reliability, resulting in remarkable audio fidelity from an efficient design. The 2-channel amplifier is simple to use and includes a network control & monitoring, an advanced DSP circuit, and an easy-to-use, front-panel interface.
The amplifier is capable of driving up to 100Vrms speaker loads without requiring a transformer and comes pre-loaded with JBL speaker tunings to help make installations quicker and easier. The CDi 2|1200 features an Ethernet port for using HARMAN’s HiQnet Audio Architect software for configuration and operation over a standard TCP/IQ network. The rear panel includes terminal block inputs and barrier strip outputs.
DriveCore Technology: patented DriveCore integrated circuit combines hundreds of discrete circuits into one chip for better performance, lower power consumption, and improved reliability
Supports configuration and control using HiQnet Audio Architect
Monitoring and control over TCP/IP
Color LCD and front-panel user interface for amplifier configuration, control, and monitoring
Programmable GPIO (general purpose input/output) control port
Digital signal processing (input/output EQ filters, crossover, input/output delay, LevelMAX limiters)
Support for importing of FIR filter coefficients
20 device presets—1 factory and 19 user
96 kHz/32-bit floating-point signal processing
Universal power supply with PFC for reduced current draw and industry-leading efficiency
Power saving modes
Remote power off—Sleep mode activated via AUX port
70/100Vrms direct drive
Each channel independently configurable for low z or high z operation
Advanced protection circuits—amplifier and loads are protected against shorted outputs, DC, mismatched loads, overheating, over/undervoltage, and high-frequency overload
Three-year, no-fault transferable warranty—your investment is fully protected
Complies with GreenEdge by HARMAN—environmentally friendly practices in design, manufacturing, and packaging complement energy-efficient operation
Support for BSS Audio Soundweb Contrio Ethernet wall controllers
Included speaker tuning for various JBL speaker models
Number of Channels 2
Power Rating
1200 W per Channel
2400 W Bridged
Load Impedance / Voltage
Stereo:
2 / 4 / 8 / 16 Ohms per Channel
70 / 100 V per Channel
Bridged:
4 / 8 / 16 Ohms
140 / 200 V
Performance
Protections DC Fault, Low Impedance, Open Circuit, Overcurrent, Overvoltage, Ultrasonic, Undervoltage
Frequency Response 20 Hz to 20 kHz ±0.25 dB (8 Ohms)
Damping Factor > 1000
Input Sensitivity
Line:
0.7 Vrms to 2.5 Vrms / -.8 dBu to 10.2 dBu (at 8 Ohms)
1 Vrms to 3.5 Vrms / 2.2 dBu to 13.2 dBu (at 70 V)
1.4 Vrms to 5 Vrms / 5.2 dBu to 16.2 dBu (at 100 V)
Input Impedance
10 Kilohms (Balanced)
5 Kilohms (Unbalanced)
Max Gain 34 dB (at 4 Ohms, at 8 Ohms, at 70 V, at 100 V)
Max Input Level +20 dBu
SNR > 104 dB
THD 0.35% (at Rated Power)
Intermodulation Distortion ≤ 0.35%
Crosstalk > 80 dB (Below Rated Power)
CMRR > 70 dB
Signal Processing
DSP 32-Bit Floating Point DSP at 96 kHz
Audio Delay Adjustable Up to 1000 ms per Channel
Crossover
High-Pass:
16 to 20 kHz, 12/24/48 dB/Octave Bessel
High-Pass:
16 to 20 kHz, 6/12/24/48 dB/Octave Butterworth
High-Pass:
16 to 20 kHz, 12/24/48 dB/Octave Linkwitz-Riley
Low-Pass:
16 to 20 kHz, 12/24/48 dB/Octave Bessel
Low-Pass:
16 to 20 kHz, 6/12/24/48 dB/Octave Butterworth
Low-Pass:
16 to 20 kHz, 12/24/48 dB/Octave Linkwitz-Riley
EQ 8-Band Parametric EQ per Channel
Limiting Yes
Connectivity
Analog Audio I/O
1 x Block 6-Pin Balanced Line Input
1 x Barrier Strip 4-Pin Speaker Output
Digital I/O 1 x RJ45 Ethernet Input/Output (Control)
USB None
Power
AC Input Power
Universal: 100 to 240 VAC, 50 / 60 Hz
AC Power Connector 1 x IEC 15 A / NEMA 5-15
Current Consumption
120 VAC:
3.6 to 7.2 A (1/8 Power)
5.4 to 9.1 A (1/3 Power)
230 VAC:
2 to 2.1 A (1/8 Power)
4.5 to 4.9 A (1/3 Power)
Power Consumption
120 VAC:
130 to 167 W (1/8 Power)
204 to 265 (1/3 Power)
230 VAC:
117 to 149 W (1/8 Power)
196 to 313 (1/3 Power)
Physical
Display & Indicators
Front Panel:
1 x Multi-Color Graphic LCD
Rackmount Size 2 RU
Cooling Fan (Variable Speed)
Thermal Dissipation 1068 BTU/hr (Maximum)
Dimensions 19.0 x 3.5 x 14.7″ / 48.3 x 8.9 x 37.4 cm
Weight 17.2 lb / 7.8 kg
Packaging Info
Package Weight 20.61 lb
Box Dimensions (LxWxH) 21.8 x 21.1 x 7.9″
